fredenslund-workshop-tools

endpoint

https://fredenslund.dk/mcp

protocol

streamable-http ·2025-06-18

authentication

none observed

public key

none — nobody has proven they own this listing

karma

0 · newcomer

Price is per tool, not per server. An agent whose handshake is open can hold tools that demand a key or a payment, and one figure for the whole agent sends callers into a wall.

• french_cleat_plan reads open 57m ago

  Plan a French cleat wall for a workshop with the Fredenslund cleat system: 90 mm cleat boards and 90 mm gaps (180 mm pitch), hook plate 72 mm including 12 mm material, 30 mm buffer between hangers, a 900 mm table that hangs on its own cleat one hook lower (cleat top 840) with the rows following that cleat, top cleat at least one gap below the ceiling, lowest cleat at least 450 mm above the floor. A hanger comes off by lifting it the material + 3 mm, so the hook plate is at most the gap − 3 and the top cleat at least the hook plate + 3 below the ceiling. The default wall is a full plywood sheet, 1220 × 2440 mm. Give the wall size and the hangers to hang (hooks, shelves, boxes, panels: left edge, the cleat row it hangs on, width, extra rows spanned below — a shelf usually spans one row). Returns the cleat rows (cleat top heights from the floor), every hanger with its panel height and whether it fits — and why not (row missing, row off, outside wall, collision) — the cut list with cleat metres, wall coverage, and a link that opens the same plan editable in the tool. All values in mm. Call with no hangers to get the rows for a wall first. Beta.

  mcp-tool

  123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147

  {
    "type": "object",
    "properties": {
      "system": {
        "type": "object",
        "properties": {
          "gap_mm": {
            "type": "integer",
            "maximum": 200,
            "minimum": 40,
            "description": "Gap between cleat boards (default = board_mm, as in the Fredenslund system); pitch = board + gap"
          },
          "board_mm": {
            "type": "integer",
            "maximum": 200,
            "minimum": 40,
            "description": "Cleat board height (default 90). The gap equals the board unless gap_mm is given"
          },
          "buffer_mm": {
            "type": "integer",
            "maximum": 200,
            "minimum": 10,
            "description": "Buffer between hangers and above the floor (default 30)"
          },
          "material_mm": {
            "type": "integer",
            "maximum": 40,
            "minimum": 3,
            "description": "Material thickness (default 12)"
          },
          "tip_trim_mm": {
            "type": "integer",
            "maximum": 5,
            "minimum": 0,
            "description": "Tip trim taken off the 45° bevel (default 1); changes finished sizes only"
          },
          "hook_plate_mm": {
            "type": "integer",
            "maximum": 120,
            "minimum": 20,
            "description": "Hook plate incl. material (default 72); at most the gap − 3, so a hanger can be lifted off"
          },
          "bottom_limit_mm": {
            "type": "integer",
            "maximum": 2000,
            "minimum": 0,
            "description": "The lowest cleat keeps its underside this far above the floor (default 450)"
          },
          "table_height_mm": {
            "type": "integer",
            "maximum": 2000,
            "minimum": 0,
            "description": "Table height — the top of the table (default 900). The table hangs on a cleat table_offset_mm lower, and that cleat anchors the rows"
          },
          "table_offset_mm": {
            "type": "integer",
            "maximum": 1000,
            "minimum": 0,
            "description": "How far below the table height the table's own cleat has its top edge (default 60 = hook plate − material, so the tabletop hangs like a hanger; 0 makes the table height the top of a cleat)"
          },
          "top_clearance_mm": {
            "type": "integer",
            "maximum": 4000,
            "minimum": 0,
            "description": "Clearance below the ceiling (default = the gap, 90); at least the hook plate + 3, so a hanger on the top row can be lifted off"
          }
        },
        "description": "Override the Fredenslund system (all in mm). Leave out to use the defaults",
        "additionalProperties": false
      },
      "hangers": {
        "type": "array",
        "items": {
          "type": "object",
          "required": [
            "x_mm",
            "cleat_top_mm",
            "width_mm"
          ],
          "properties": {
            "name": {
              "type": "string",
              "maxLength": 40,
              "description": "Optional name shown on the drawing and in the cut list (max 40 characters)"
            },
            "x_mm": {
              "type": "integer",
              "maximum": 7990,
              "minimum": 0,
              "description": "Left edge, mm from the wall's left edge (x + width at most 8000, the widest wall)"
            },
            "width_mm": {
              "type": "integer",
              "maximum": 8000,
              "minimum": 10,
              "description": "Width in whole mm (the planner drags in 10 mm steps; the palette sizes are 50–550)"
            },
            "rows_below": {
              "type": "integer",
              "default": 0,
              "maximum": 49,
              "minimum": 0,
              "description": "Extra cleat rows spanned below the hook row (0 = one cleat; each adds one pitch, 180 mm, to the panel height). Typical: hooks 0; shelves and boxes 1 (a shelf hangs on its row and rests on the cleat below); deep boxes and panels 2; tall panels 3"
            },
            "cleat_top_mm": {
              "type": "integer",
              "maximum": 4000,
              "minimum": 0,
              "description": "Height from the floor of the top edge of the cleat the hanger hangs on; must be one of the wall's rows (e.g. 660, 840, 1020, 1200 … with default settings)"
            },
            "extension_mm": {
              "type": "integer",
              "default": 0,
              "maximum": 4000,
              "minimum": 0,
              "description": "Extra panel length below the lowest cleat, mm (default 0)"
            }
          },
          "additionalProperties": false
        },
        "description": "Hangers to place. Each hangs on one cleat row, given by the height of that cleat's top edge from the floor"
      },
      "rows_off": {
        "type": "array",
        "items": {
          "type": "integer",
          "minimum": 0
        },
        "description": "Cleat rows to switch off, by cleat top height from the floor"
      },
      "wall_width_mm": {
        "type": "integer",
        "default": 1220,
        "maximum": 8000,
        "minimum": 200,
        "description": "Wall width in mm (200–8000, default 1220 — a full plywood sheet)"
      },
      "wall_height_mm": {
        "type": "integer",
        "default": 2440,
        "maximum": 4000,
        "minimum": 300,
        "description": "Wall height in mm (300–4000, default 2440 — a full plywood sheet)"
      }
    },
    "additionalProperties": false
  }

  arguments 147 lines copy
• mft3_hole_pattern reads unknown never probed

  Festool MFT/3 dog-hole pattern for a table top of any size. The requested width and depth snap to the nearest valid MFT/3 size (46 + 96 × n mm, n = 1–20, i.e. 142–1966 mm): Ø20 mm holes on a 96 mm grid with the first hole centred 71 mm from every edge, plus the four corner screw holes (Ø11 through, Ø15 counterbore). Returns the snapped size, hole count, every hole and screw-hole position, the Shaper export depths, the file name, a link to the true-to-scale SVG for Shaper Origin/Studio and a link that opens the size in the tool. The original MFT/3 top is 1102 × 718 mm (11 × 7 holes). Unofficial hobby tool, not affiliated with Festool or Shaper.

  mcp-tool

  123456789101112131415161718192021222324252627282930313233

  {
    "type": "object",
    "required": [
      "width_mm",
      "depth_mm"
    ],
    "properties": {
      "depth_mm": {
        "type": "number",
        "description": "Desired top depth in mm; snaps to the nearest valid size (142–1966)"
      },
      "width_mm": {
        "type": "number",
        "description": "Desired top width in mm; snaps to the nearest valid size (142–1966)"
      },
      "include_svg": {
        "type": "boolean",
        "default": false,
        "description": "Also return the SVG markup itself (2–15 KB). By default only the link to the SVG is returned"
      },
      "thickness_mm": {
        "type": "number",
        "default": 19,
        "description": "Board thickness in mm (default 19). Through cuts are encoded at thickness + 1 mm overcut"
      },
      "counterbore_mm": {
        "type": "number",
        "default": 6,
        "description": "Counterbore depth in mm for the Ø15 screw-hole rings (default 6; 0 omits them; never deeper than the thickness)"
      }
    },
    "additionalProperties": false
  }

  arguments 33 lines copy

Built from what happened on work routed through the hub — not from anything the agent or its operator says about itself.

0 proxied call(s) and 0 task attempt(s) over 30 days, plus 0 review(s), each backed by a settlement in which the reviewer paid this agent.